New valve covers and exhaust!

[Muchbzy]

Well, it took me a while but I finally had the time to get this work done to the car. Let me know what you think. :D

http://photos.yahoo.com/muchbzy

[zank]

Awsome pics. I love the color of your car :P.

[rsdeo]

Nice job.

[3000cc MK2]

hey Cee-Jay... when will I have a chance to see your SUPRA... :lol:

[trdmkii]

wow very nice supra, that paint job is amazing. I love the contrast of the colors, beautiful car!!!!!!!!!!!!

[Muchbzy]

hey Cee-Jay... when will I have a chance to see your SUPRA... :lol:

Couple of small things to do and I'm all over the meet in MD. I didn't get to finish the MA70 alternator swap so I gotta go back for that and I'm trying to replace the hood insulation. :wink:

[3000cc MK2]

so are you still available this SAT for the Battle... we are going but no MK2 will run... the white supra is still torn apart for the T3/T4 turbo and I think it will be ready for the NOPI at aug... we might just support Velocity Racing on thier MR2 Turbo w/ upgraded CT-26 and I am still 50/50 if I will run for bracket and see how the built 6MGE 8.0:1 engine will do on the 1/4 before hooking up the CT-26 on July

Jay

[Carlos_Relova]

Looks really good.

What exhaust is that?
Also, which electric fans do you have and how are they installed?

Regards,
Carlos

[Speed Racer]

Well, it took me a while but I finally had the time to get this work done to the car. Let me know what you think. :D

http://photos.yahoo.com/muchbzy

Beautiful car Cee-Jay...love the turbo install. Very clean, nice work. I like the red valve covers too, looks really sharp with the red intake piping.

I'll do the conversion someday, just too many $$$ priorities right now.

[Muchbzy]

so are you still available this SAT for the Battle... we are going but no MK2 will run... the white supra is still torn apart for the T3/T4 turbo and I think it will be ready for the NOPI at aug... we might just support Velocity Racing on thier MR2 Turbo w/ upgraded CT-26 and I am still 50/50 if I will run for bracket and see how the built 6MGE 8.0:1 engine will do on the 1/4 before hooking up the CT-26 on July

Jay

No, sorry to say. With the things that came up this weekend I haven't finished the little things. Trying to schedule the rest for this weekend so I can be totally ready for MD.

[Muchbzy]

Looks really good.

What exhaust is that?
Also, which electric fans do you have and how are they installed?

Regards,
Carlos

The muffler is one I found on Ebay and researched. It comes from a company called PowerTech. The ends are resonated and are 4inchers! The pictures don't do them justice. The pipe is 2.5 aluminized steel. Very rust resistant. :wink: Since I can't afford SS! The fans are 12 inchers from like Auto Zone with a thermostat (that I probably have turned too low) and they are attached with the ties that go through the fins. I don't like that set up but that's how the instructions are written.

[Malibyte]

Very nice....like the rims. Who makes 'em and where did you get 'em, and for how much??

-- Bob --
(looking for new rims for the Redpra)

[3000cc MK2]

OK... Fred is not coming either this saturday due to the corvette meet in va beach... well I will be bringing the supra this sat and if I am all charged up this weekend... I might end up fighting again in S/E C bracket racing and hope to clinch the throphy again since last year in MD...

well just earlier I just finished hooking up the wires for my line-lock and 2step rev limiter.... dang that thing works... now I can get a good hole shot from the light and still be consistent with my launch rpm and also the famous burn-out of the Mickey's

well I am gonna try and take videos and pics and will soon post some up next week... hopefully

Jay

[Muchbzy]

Very nice....like the rims. Who makes 'em and where did you get 'em, and for how much??

-- Bob --
(looking for new rims for the Redpra)

ARE, American Racing Equipment, wheels that I got from Pep Boys, YEARS ago at about 139.00 a wheel but I got them for about 99.00.

[Usagisama 83']

WOAH. That looks great! Super nice job, you can really see the time you spent on it. I hope my car will be that cool someday!

[Henge]

muchbzy...did you custom make that cold air pipe? I want one 8)

[Muchbzy]

muchbzy...did you custom make that cold air pipe? I want one 8)

My shop made it for me and I had it powder coated. They kept a template if you are really interested.