Results 1 to 10 of 15
Thread: walbro 255 install HELP
-
10-10-2012, 12:15 AM #1
Member
- Join Date
- Sep 2011
- Location
- Lakewood, CO
- Posts
- 70
walbro 255 install HELP
Now I'm sure I'm stupid but, I'm trying to install this walbro 255 I got from chimp and it only came with 2 barb fittings? What's up with that? I understand the one side but how am I supposed to get the pressure fuel line hose where the banjo type fitting was located? That will not work with a barb for sure.. help please I'm dumb =l
"Cheap, Fast, Reliable, pick two and thats what you get in a car"
-
10-10-2012, 07:50 AM #2
CelicaSupra.com Member
- Join Date
- Jul 2003
- Location
- Lake Mills, Wisconsin
- Posts
- 3,342
In-tank?
Dave Harrison
'85 Mark2 7mgte 5sp
'85 Mark2 7mgte Auto
'85 Mark2 7mgte 5sp
-
10-10-2012, 09:31 AM #3
Member
- Join Date
- Sep 2011
- Location
- Lakewood, CO
- Posts
- 70
Its an 82 sorry, so in line not in tank
"Cheap, Fast, Reliable, pick two and thats what you get in a car"
-
10-10-2012, 11:37 AM #4
CelicaSupra.com Member
- Join Date
- May 2004
- Location
- Windsor, Ontario
- Posts
- 6,293
I think you cut the banjo's off so you can slide in the barbs and hose clamp. I could be wrong though. Check with Aaron.
86 Black MA67: 87 7M, 300hp, no shit! 84 Brown MX63: It's a Dork, not Donk!
Check out some 7M Supra Videos!
Links: My 7M-GTE swap guide Electrical FAQ 85 MA61 TEWD 86 MA61 TSRM 87 MA71 TSRM 90 MA71 TSRM
Originally Posted by Tire Shredder
-
10-10-2012, 01:12 PM #5
Member
- Join Date
- Sep 2011
- Location
- Lakewood, CO
- Posts
- 70
I thought it was pressure line but it could be, anyone confirrm this?
"Cheap, Fast, Reliable, pick two and thats what you get in a car"
-
10-10-2012, 01:24 PM #6
Member
- Join Date
- Aug 2012
- Location
- Midvale, Utah
- Posts
- 41
I'd like to know also!
-
10-10-2012, 02:49 PM #7
CelicaSupra.com Member
- Join Date
- May 2004
- Location
- Windsor, Ontario
- Posts
- 6,293
The pump is on the pressure line. The hose going to the tank is the feed line for the pump, and the one going to the motor is the pressure line. You could cut the banjo fitting off the rubber hose and use slide the barb in and clamp it. I'm pretty sure that would be how the chimp would intend it, if that is what he sent you. Check with him first if you are unsure.
86 Black MA67: 87 7M, 300hp, no shit! 84 Brown MX63: It's a Dork, not Donk!
Check out some 7M Supra Videos!
Links: My 7M-GTE swap guide Electrical FAQ 85 MA61 TEWD 86 MA61 TSRM 87 MA71 TSRM 90 MA71 TSRM
Originally Posted by Tire Shredder
-
10-10-2012, 10:44 PM #8
CelicaSupra.com Member
- Join Date
- Aug 2005
- Location
- near Baltimore, MD
- Posts
- 1,074
Sounds like you bought an in tank pump for an external setup?
82 7MGTE, W58, SP61/upgrded elbow, Spearco IC, P&P, 2.0MHG, VPC/SAFC2, LM-1 Wideband, Full 3in, TRD rear, Springs/Shox, Cold A/C, 85 deck
89 7MGTE, SP67 @ 18lbs, VPC/SAFC2, Spearco Front Mount, 550 inj, full 3inch exhaust
WANTED: KAMINARI/EREBUNI front lip
-
10-11-2012, 01:08 AM #9
CelicaSupra.com Member
- Join Date
- Nov 2004
- Location
- Graham, WA
- Posts
- 5,076
See if the silencer threads on the output of the pump before you go cutting anything.
-Chris
1983 Celipra GTS:
6M bored .50 over. 250cc injectors. Delta 272 regrind cams. Carter HF fuel pump.
Pacesetter header w/2.5" cutsom exhaust. Open air intake filter. 3" piping to TB. 65mm TB & ported AFM.
4:10 rear from Supra. BillyM shifter kit. Swapped most interior over to black. T3 camber plates.
935 Budget Coilover kit. KYB AGX struts. T3 Needle bearing upper perch kit. Eibach Sport rear supra springs. SF Ford TFI Performance coil.
Almost finished with the fiberglass hatch!
-
10-11-2012, 05:18 PM #10
Member
- Join Date
- Sep 2011
- Location
- Lakewood, CO
- Posts
- 70
Silencer doesn't thread its a much smaller thread size, and nope it was the in line one because the in tank one comes with diferent hardware.. idk how this is supposed to work..
"Cheap, Fast, Reliable, pick two and thats what you get in a car"
Reply With Quote
Thread Information
Users Browsing this Thread
There are currently 1 users browsing this thread. (0 members and 1 guests)
