found a JDM mugen twin loop

[scottevil]

Yea thats what i want but i cant afford a $600 exhaust system right now. i have an aftermarket one on there now from previous owner but im not sure of size i havent meaured yet. i did find this for the 2.25 though. i could put a cheap auto parts store tip on it.
http://www.ebay.com/itm/Flowmaster-M...2c51ed&vxp=mtr

yea measure the diameter of you're pipe. they make adapter for most sizes. Talk to one of the vendors either Aaron from rabid Chimp or George from Raptor Racing they will most likely be able to get a decent muffler for you at a good price.

[ihateu3]

NISMO muffler on a Ford sounds the best! lol

[little-red-supr]

Ok I found a 3" stainless steel pipe that bolts up to the stock cats for $180 on eBay I might go for that and find a magnaflow muffler to go with it. Yea and luckily it's free shipping too!

[StanS]

iirc catback dia is 1.98"

[Tanya]

Yea but if it fits it'd be nice I just want a rich deep tone for 200 under

Then get a turbo or a large displacement 4 cylinder. you're not going to get a deep tone otherwise.

My engine has the largest diameter primary header, 2.5" exhaust and magnaflow muffler and sounds like a freakin Gixxer above 3500k rpms.

[Morg_9]

Ok I found a 3" stainless steel pipe that bolts up to the stock cats for $180 on eBay I might go for that and find a magnaflow muffler to go with it. Yea and luckily it's free shipping too!

As far as I've seen of these, they're Chinese copies of the Raptor Racing exhaust available from Raptor Racing right here on this forum. That's what any that I've seen on there look to be. Support the vendors, which support the forum. Buy legit. Check out Raptor's (and RabidChimp's) stuff and give us a link to this Chinese eBay one if you think otherwise. Also, if you're staying NA (not going turbo), 3" is considered a little too big - better off with 2.5".

[little-red-supr]

yea i see what you mean on the 3" being too big for a N/A but i cant find a cheep 2.5 and i cant afford the raptor or rabid chimp. If i had that much i would but its really expensive! At max 250 including shipping is what i can really afford at the moment. But anyway this is the one i was lookin at.
http://www.ebay.com/itm/New-84-Toyot...517693&vxp=mtr

[REN69]

that's only the midpipes... there's no muffler included... the RR mid-pipes are $275 FREE SHIPPING so you're paying about the same... Actually more on that ebay link, since $180.01 + $97.20 = $277.21, lol... not to mention since it's coming from China you could incur customs/brokerage fees.

George has FULL EXHAUST meaning midpipes and muffler for $545... add a cat if you need one, chances are if you're still stock you'll need one... I added the metallic cat AND test pipe, been running on test pipe since the summer.

the RR and RC pipes are quality pipes, I actually got to meet the guys that make this possible for George back in March when I had my exhaust done, good guys and really good shop.

[maximaj30]

Then get a turbo or a large displacement 4 cylinder. you're not going to get a deep tone otherwise.

My engine has the largest diameter primary header, 2.5" exhaust and magnaflow muffler and sounds like a freakin Gixxer above 3500k rpms.

every NA V6 or straight 6 vehicle ive built has had a deep tone. only way youre gonna get raspiness is if you dont use a good resonator.