Results 1 to 10 of 279
Thread: 7mgte swap FAQ
04-03-2005, 06:01 PM #1
- Join Date
- Mar 2003
7mgte swap FAQ
This is by NO MEANS done,needs blanks filled and finished etc.But,hopefully this will help.I'll work on it more later.
7MGTE General MKII Swap.
This write-up is the way I learned to do the swap.There are many differing opinions on several aspects of this swap.I'm not going into those details,just writing what I know personaly.This will basicaly be for a stock swap,with some performance talked about.
1st off,you need a complete 7mgte,with all of it's sensors intact.Must have....Intact engine harness,preferably with any plugs and all small electrics,that plug into it.Air Flow meter,ECU,HAC sensor if 87-8.Included should be the PS pump,and brackets,and A/C pump and bracket.The more complete the better,a running donor car is obviously best.
My basic list,in no particular order.
1.7mge clutch kit,preferably a performance unit.
2.ARP head stud kit. P/N 203-4202
3.Oil filter relocation kit. ford 5.0 PN depends on brand.
4.4 90* AN - 8,and 4 -8 AN adapter fittings. 8 ft 300psi hydrolic line.
5.Toyota T100 heat shield p/n 58151-34011
6.7mgte gasket set.
7.HKS or similar metal head gasket.
8.MKIII intercooler and all plumbing,or custom,either will work.
9.Custom A/C lines to mate MKII to 7mgte a/c compressor.
10.MSD tach adapter.P/N 8920
11.85 or newer 5mge oil pan,and new 85+ oil pump.
I usualy tear the engine down to a short block,inspect cylinder walls,and check bearing clearances.Basic short block is repair as needed.Pistons and rings,only if needed,or forged units are being installed.Bearings,very seldom do they need mains,I usualy replace rod bearings as they are cheap.
Block/head mating suface.Personaly,I clean it well,check it with a straight edge,and don't worry about too much,unless it's noticably in bad shape...ie...warped or pitted.In that case,that block gets set aside for a major build up,or just tossed.
Cylinder head.Pressure tested,and a light "dusting" surface job.I prefer to still be able to make out the old gasket marks,barely.Then,the valves get hand lapped in and new seals installed.I recomend for most,to just have the machine shop do a valve job.I just prefer to do my own work.
Some where about this time,I relocate the dipstick to the 5m location.Starting with a small pilot hole,then drill to size of DS."have to get size" Then plugging the old hole with an allen type pipe plug.
Next would be the rear aluminum timing cover "frt of engine" and all related seals.Then time for the Oil Pump.Rotate the crank a few times,or until it touches the pump housing,or banjo portion of the tube.Some touch,some don't.Remove,and grind as necesary,until crak clears everything.Put the pan on and flip it over.
Whether using a MHG or a stocker,I spray the gasket with Permatex copper gasket spray.This helps out with the block/head surface imperfections,and has yet to fail me in 30years of building various engines.
Cylinder head instalation.Personaly,I use a metal gasket,usualy 1.2mm by HKS,along with ARP head studs.1st off,remove the cams if not already out,they just get in way.Next,istall the washers,in there respective spot,NOW.You'll thank me later.Make sure the washers go down the studs,with the head.It takes a bit of patience,but it's the only way they go in on most heads.Torque to ARP spec,IIRC 95ft#.
If usinf a stock HG ,torque to 65-70ft lbs,NOT the 58 suggested by the TSRM.For stock application/boost,this will last as long or longer than the rest of the engine.
The rest of the basic engine asembly,is covered in any Supra manual,so I not going into detail on that.
Oil filter adapter..........If using the stock 7mgte 90* housing,you will need to rotate it counter-clockwise,OFF it's dowel pin.Torqueing it down,Just to the left of the pin,will allow clearance foe the motor mounts.Check the BGB for torque spec on the bolt holding the 90.IIRC "book in the shop" it's 14 or 17ft lbs.THIS IS CRITICAL !!! If you over torque this bolt,you WILL crack the bung in the block "ask me how I know".
If deleting the stock 90,I have found it best to rob the oil filter "bolt" from the 5m,then add the 5.0 in/out adapter,and then position the AN fittings and oil lines.
Motor mounts...use the stock MKII units,holes are in the block,forward position.For the turbo brace,which now has no place to go,get an early MKIII pass mount,block portion.Angle cut the mount,so as to leave the hole for the turbo brace,bolt it behind the mkii mounts,at stock mkiii location.
While the engine is out of the car,time to clean things up a bit.Personaly,I lose the stock washer tank and pump set-up...don't use headlite washers anyway.I also toss the big friggin carbon canister the mkii comes with,and replace it with one from an 87-91 4 cyl camry.I also relocate it to where the Waher system was.The is 1 bolt hole,on thew inner fender,and a hole for the "breather" tube on the camry unit to go through.I usualky drill a hole for the second screw,a bit oversize,as I never seem to get the measurement dead on :P For W/S washer,I get a bag from the rear of an 84-9 4-runner,build an extension harness,and mount the bag on the drivers shock tower.
I also,in the past have mounted the oil filter relocation adapter,in the area of the washer tank,on the pass. shock tower.Makes getting the filter off a piece of cake.I'll be changing this on Ophir's car,and my own,as the larger turbos generate a bit more heat in that area,than I'm happy with :lol:
New loaction to be posted,when I find a spot I REALLY like.Probably similar to Helmsman's install,by the pass. head light.84 P-type, 7mgte, too many other mods to list, 20k miles on the chassis. 83 L-type, 7mgte/A340 swap, again, to much to list. 85 P-type, basicaly stock, DD.
Sponsored Links Remove Advertisements
04-04-2005, 12:55 AM #2
Shawn, you might change the title to: "7mgte swap FAQ" or "7mgte swap how to's in here". Perhaps caps might get some attention.
04-04-2005, 01:22 AM #3
Sponsored Links Remove Advertisements
04-04-2005, 01:54 AM #4
- Join Date
- Mar 2003
Junkie.. i think that also.. posting part #'s on the swap parts like MSD and oil filter relocating kit would also help..keeeping down all the little questions.
04-04-2005, 02:38 AM #5
MSD tach adapter is #8920
the oil filter relocater to get is one for a ford 302 (5.0L), and the AN adapter fittings/90 degree fittings and stainless hose are an optional upgrade to the crappy rubber hose and barbed fittings that come with the usual oil filter relocation kits
i should also mention that you will need to use the W58 clutch bits with the W58 flywheel from the 5mge, as well as your old 5m engine mounts, clutch cover and engine to transmission lower stiffener plates
plus you gotta grind the AC compressor bracket a bit to the the mount under it
and then there is running the IC piping and the wiring
and you gotta use a pod style air filter cuz the stock one wont fit - and the exhaust needs to be custom (unless you get a chimpy downpipe)'84 P-type, 5spd, Super red, black/grey leather - 2JZGTE swap, Precision 6262 on cast manifold, ECUmaster black with 875cc/min injectors, 465 WHP at 17 psi, built R154 with OS Giken twin plate, one piece driveshaft with 1310 joints, Truetrac with 3.73 R&P, 450 lb/in front coilovers, 300lb/in rear springs, Image BBM wheels 17x8 and 18x10, 4 corner BBK, AGX shocks, Whiteline bars, poly bushings, T3 GTX2 front control and steering arms etc. etc.
04-04-2005, 09:52 PM #6
- Join Date
- Mar 2003
Thanks Mike :wink:
Wayne,I'm working on it,just a start.Most from memory,as my notes are not where I remeber :roll:
Funky,thanks for the addition,I'll be working as much in as I can.
ALL.....anything is appreciated.....I just REALLY want to get as much in one thread,as possible.
If anybody has a question they need answered,this is the spot.Doing so here will allow me "and anyone else" to answer,then I can cut/past edit,etc. to get most in the proper order.
I'll be working on this over the next week or two,to get this to be fairly complete.
Thanks84 P-type, 7mgte, too many other mods to list, 20k miles on the chassis. 83 L-type, 7mgte/A340 swap, again, to much to list. 85 P-type, basicaly stock, DD.
04-04-2005, 10:59 PM #7Originally Posted by Funkycheeze
Oil Filter Relocation kit
Summit Racing Parts #: TRD-1113
Flex-a-Lite Electric fans (not needed for the swap)
Summit Racing Parts #: FLX-21085 Starfire Pearl 6MGE 5spd
85 Jet Black 7MGTE 5spd
04-24-2005, 04:09 AM #8
more to add:
if using 5m rad, you need to use a 7m upper rad hose (cut to fit) and a 5m lower rad hose, as well as the 5m heater hoses, however
if you have a 87-88 block, there will be a 'cap' on one side of the heater fitting on the back of the head, move this to the other side, and you can use the stock 5m 'suicide' hose
BUT if you have the 89-91 block, you need to use a custom chunk of water hose, since the only fitting is on the 'wrong' side
for the fuel system, you mount the 5m filter/bracket assy to the side of the 7m block, and attach the banjo from the fuel rail to the top (use NEW crush washers on all the fuel system banjo fittings) and then attach the feed line to the filter as it was with the 5m
you can then simply attach the J tube to the fuel return, as per 5m
its also a good idea to use a walbro intank pump to replace the stocker'84 P-type, 5spd, Super red, black/grey leather - 2JZGTE swap, Precision 6262 on cast manifold, ECUmaster black with 875cc/min injectors, 465 WHP at 17 psi, built R154 with OS Giken twin plate, one piece driveshaft with 1310 joints, Truetrac with 3.73 R&P, 450 lb/in front coilovers, 300lb/in rear springs, Image BBM wheels 17x8 and 18x10, 4 corner BBK, AGX shocks, Whiteline bars, poly bushings, T3 GTX2 front control and steering arms etc. etc.
04-24-2005, 10:53 AM #9
- Join Date
- Mar 2003
Thanks for the addition Funky.I haven't had a chance to work on my engine,or the write up for a couple weeks.
Again,ANYBODY with a few words of wisdom,please add to this.
I have noticed,since this was started,there have not been any questions about the swap.
I am planning on adding some pics also,just need to dig thru a couple hardrives84 P-type, 7mgte, too many other mods to list, 20k miles on the chassis. 83 L-type, 7mgte/A340 swap, again, to much to list. 85 P-type, basicaly stock, DD.
05-01-2005, 01:27 AM #10
Junkie, I have the complete list with part #'s from my original kit documents. I will bring them over and you can add them to this thread.Don C. (-Professional Lurker-)
Built and Sold 2005:
"Agatha" 1984 P-Type,5spd,7MGTE powered,273whp.
Winner of more awards than any other Supra in the history of Supras Invade Las Vegas.
Latest Build and Sold 2009:
"Athena" 1985 P-Type,AT,Hard Top,7MGTE powered.
(thousands less than Agatha sold for).
check out pics:
Users Browsing this Thread
There are currently 2 users browsing this thread. (0 members and 2 guests)