Toyota Celica Supra Forum banner

Wobby idling

3K views 35 replies 10 participants last post by  Zoe 
#1 · (Edited)
Hi specialists. I was driving my car to an event where we stayed for a couple of hours, car was not running. No problems so far. When we left the event, I noticed the CEL was on and the car was running poorly. It seemed to run very rich, did not respond to the pedal very well. Immediately tried to read the codes with shorting the connector but it did not work.

Drove (as well as I could) the car back to my garage and tried again to read the codes, still no success.

Replacing the plugs was the first, easy choice - not helping. Checked the distributor, it was rusty but cleaning did not change anything.

I noticed the cam towers were leaking oil so I took the engine into pieces, replaced the seals and thought I might also take the injectors to a shop while everything is now taken apart. Injector maintenance was completed and the engine was put back together. It runs better (3 injectors were leaking and output was bad in 2 units) now, but idle still changes between 500-1000rpm all the time. Also, CEL is still on.

I thought perhaps the wiring is a problem in the connector so I shorted the pins in the ECU connector to be able to read the codes - still nothing. CEL just stays on and will not blink.

Someone proposed to use the old, analog type of reading codes, but there is supposed to be 3 diagnostic connectors and my car only has 2 so that also does not work.

Next task was to start doing the diagnostics according to the manual I found online in the group Facebook page. That manual seems to be for a newer model since my car has the older model of TPS and there is no Idle Speed Controller as stated in the manual. So I tried measuring resistances and voltages from the ECU connector but this is not working since the values are for newer model. Of course some of those work, for example ECU seems to have power and grounding properly. Most of the wires are the same as in the manual anyway.

This has taken weeks now and I just cannot figure out what could be causing this. Any help is much appreciated. Thank you for taking some time to read my long post.
  • What can possibly make the idle go up and down like this?
  • What will make the CEL stay on no matter if I short the diagnostics connector? Grounding?
  • What devices will be checked when the ECU diagnoses the system? Temp sensors and TPS, of course but what else? Signal from the distributor when cranking? Anything else I should check?
  • Is there a repair manual somewhere online for the older model?
edit: MA61, 5M-GE, 1984/1985 Euro-spec
 
See less See more
#2 ·
I started to make a wager what it was, but noting you're from Finland and some mention of not having an iacv, maybe we better understand which year model and which engine you have before we start guessing.
 
  • Like
Reactions: 85midnightsupra
#3 · (Edited)
Uh, stupid me. I thought I had the car info in my signature but apparently not. Sorry about that, added it to the end of my post. MA61, 5M-GE, car is probably 1984 but registered 1985.
Motor vehicle Automotive design Space bar Office equipment Auto part
 
#4 ·
Hmmmm..... For a 1984, your market must have gotten some setup unlike what we got here in the US. I'm looking for an ISCV in the picture and all I see is a dark, apparently unoccupied space. But my guess is your throttle position sensor. I would test that first. I've seen it before where the idle speed goes up and down and up and down when the tps is unable to register the closed throttle position. Its like the computer is still doing its thing, trying to regulate the emissions, fuel mixture, timing and such in closed loop as if you were driving down the road. It doesn't know that you intended for it to go into open loop (which you told it to do by taking your foot off the gas) and lock everything into a static idle setting.
 
#6 ·
I'm looking for an ISCV in the picture and all I see is a dark, apparently unoccupied space.
Yes, I was wondering the same.

But my guess is your throttle position sensor. I would test that first.
It has been tested and I even shorted the pins to make sure ECU gets the "throttle closed" signal. Not helping.

vacuum leak.
Between AFM and intake valves

does this car have O2-sensor?
Vacuum leaks are possible but I tried searching for them by spraying brake cleaner all over the hoses. Nothing.

And no O2 sensor in this car. We did not have unleaded fuel that time so no catalyzer.
 
#7 ·
One additional question; how common is a failure in ECU in these cars? I mean, they are 40 years old anyway so components inside are very old and subject to failure. There are good instructions for the MR2 (SW20) ECU repair, wondering if there's something similar for Celica Supra?

After all, the first sentence of the article says:
"Has your MR2 been idling rough or unevenly? Is it hard to start first thing in the morning? When you come to a stop does the idle dip down a little too far and then come back up? "
 
#8 ·
With regards to the Check Engine codes, it is possible that the European 5MGE engines used an EFI system similar to the 1982 North American system which did not have a Check Engine Function.
Does your distributor have a vacuum advance diaphragm? If it does, that would indicate that your car does not have TCCS.
The Toyota Computer Controlled System was an EFI controller that electronically controlled the ignition advance. This was introduced in 1983 in North America and used an analog meter to display error codes. In late 1984/1985 the error codes were indicated by the Check Engine light flashing.
The Igniter in your picture is similar to that of the North American market 1982 Igniter, so I wonder if this is why you cannot see error codes....there are none.

North American 1982 owners may be able to help with troubleshooting if this is the case. Especially if they have a 1982 Service manual set.

Dale
 
  • Like
Reactions: dannoxyz
#10 ·
Maybe it has the IAC valve that was in the 82 US model.
Could be, as we see a hose from the overpass tube going towards the intake plenum (about 25mm dia) That could very well be the idle valve, which is simply controlled by 12V applyed to it, iirc.
 
#12 ·
Added a couple of photos just to help you see what is there in my engine bay.
Motor vehicle Automotive fuel system Automotive design Automotive air manifold Car
Gas Auto part Engineering Vehicle Close-up
Motor vehicle Automotive fuel system Automotive design Automotive air manifold Car

Gas Auto part Engineering Vehicle Close-up
 
#13 ·
I'm just trying to see how your idle speed control works. European cars seem to be slightly different from USDM vehicles in how they are equipped. As a result, I would imagine that the troubleshooting will be somewhat different.

1982 USDM cars I assume have a check engine light, but did not store check engine codes. It would light when things like the alternator regulator charging stopped working. It was a much simpler system. I really do not know if the European cars stored error codes or not.

From you latest pictures, you definitely do NOT have a vacuum advance distributor, so it does not quite compare to the 1982 USDM cars. I would imagine then that you do have the TCCS EFI/Ignition control then. However, it looks like you do have the IAC (Idle Air Control) valve of the USDM 1982. This is a simple on/off solenoid valve that bypasses the throttle blade of the throttle body to let the motor speed up slightly when things like air conditioning turn on at idle to prevent the motor from stalling.

Door Machine Metal Titanium Cylinder

IAC Valve

White Product Organism Font Line

IAC Valve plumbing on a USDM 1982. 22230A Hose leads to the air intake over the cam covers.22230B leads from the IAC Valve to the Intake manifold.

Motor vehicle Automotive design Automotive fuel system Hood Automotive exterior

1984 USDM ISC Valve

Gas Machine Auto part Metal Automotive tire

USDM ISC VAlve close-up

White Product Organism Font Line

1983 and up. Item 22270 is the ISC valve. Item 22270A leads to the air intake over the cam covers. The ISC bolts onto the front left side of the intake manifold.




By comparison, the 1983 and up USDM cars have an ISC (Idle Speed Control) valve which can step 255 discrete steps to fine tune the idle speed. The concept is the same, at idle, the valve bypasses the closed throttle blade in the throttle body to speed up or slow down the motor idle speed. As a result, the idle speed can be controlled more accurately.

Does your car have a catalytic converter? I'm just curious, because the USDM cars do, and the TCCS has errors for an Oxygen sensor. I would imagine this could affect how the system works.







Back to the original issue though, as Dannoxyz said, it sounds to me like there is an air leak between the air flow sensor and the intake. When this happens, it does not correctly match the amount of fuel being metered relative to the air flow. I would have thought that it would have run lean rather than rich, however.

Smooth idle, no throttle response

As EastClintwood found, an air leak can cause symptoms somewhat like what you describe. Idle is okay, but when applying throttle, the engine loses power and stutters. His car was a 5ME, not a 5MGE, but the concept is the same.

Unfortunately, his post no longer has the photos, but it was a leaky air hose on the intake.

Hopefully this is something simple like he found.

Dale
 
  • Like
Reactions: AJ
#14 ·
Hopefully this is something simple like he found.
Hi Dale

Thank you very much for your informative post. However, as I said in my first post, the idle is not stable but it varies regularly between 500-1000 rpm (approx.) all the time. Also, this started when the engine was off and I realized the issue when we next time started driving.

Also, if there was a leaking hose letting too much air in, I also thought the engine would run lean, not rich. I also don't think that would lit the CEL.

Uh, you also asked about catalytic converter. The answer is no. We did not have unleaded fuel that time so we did not have those that early. I believe only in the mid 90's those became mandatory.
 
#15 ·
FinToy, seems like the leaky hose may be the issue.
 
#17 ·
There is a second device that controls throttle bypass airflow as well. Possibly, it could be in this area.

If I recall correctly, it's the power steering pump system. When power steering is working hard, it can slow the motor down so there is a separate bypass circuit. If either the power steering pump or the lines leading to and from it are leaking, you could get similar issues.

Motor vehicle Vehicle Automotive fuel system Car Automotive design

Sorry for the wiggly line. Too much coffee.

Hood Automotive tire Automotive fuel system Motor vehicle Automotive exterior


These lines go down to the power steering pump and are ported.

Gas Auto part Plumbing Cable Motor vehicle

Lines to and from the power steering pump switch.
Light Motor vehicle Automotive fuel system Automotive tire Automotive exterior


Where the lines go down to and up from the power steering pump.

Light Motor vehicle Automotive tire Engineering Gas


Where the line from the power steering switch enters the intake manifold (the right or index finger).

This may have nothing to do with it, but my grandson had a Cressida that wouldn't idle because this circuit had a cracked hose. I had no idea what this stuff was before trying to help him.
Just be aware that you should leak check these lines too!

Dale
 

Attachments

#18 ·
Is the TB dirty? clean the TB butterfly plate.

Disconnect the TPS, go for a test drive, note any changes and report back.

Make sure no one has messed with the idle air adjustment screws on the TB.

Will

edit 2222 post!
 
#20 ·
In our markets, the idle device is at the end of this tube. Might be the case at your location too. As for the TPS, does not hurt to try disconnected.
Motor vehicle Light Hood Automotive design Automotive exterior
 
  • Like
Reactions: FinToy
#29 ·
In our markets, the idle device is at the end of this tube. Might be the case at your location too. As for the TPS, does not hurt to try disconnected.
View attachment 20334
Jocelyn brought up a very good question. What is on the right side of this hose? Could you take a picture of it?
This hose and whatever is attached to it is used to adjust idle speed.

For the 1982 model, the TSRM goes so far as to have one squeeze this hose shut to see the effect on idle speed.

Line Font Auto part Engineering Machine


Jaw Font Art Parallel Elbow

These pictures are from the attached section from a North American Market 1982 TSRM.
The electrical connection is just 12V and ground to apply heat to a bimetal strip which causes the valve to close as the strip heats up.

The check in step 1 really does work. When you pinch this line shut, the engine will actually stall.

Dale
 

Attachments

#23 ·
I had an intake leak between the runners and intake plenum, under the union. Was not easy to find, but fixing that cleared my idle issues about 12 years ago. Just saying it could be anywhere.

The IGt is probably ok, as it is the IGnition 't' rigger, and since you have sparks, probably ok, unless your wobby idle is misfires.

VTA being 0 or 5V indicates you have the on/off TPS. There should be another signal from the TPS indicating TPS above 71 deg, I think. (5V when it is).
 
#24 ·
I had an intake leak between the runners and intake plenum, under the union. Was not easy to find, but fixing that cleared my idle issues about 12 years ago. Just saying it could be anywhere.
Good point, thanks.

The IGt is probably ok, as it is the IGnition 't' rigger, and since you have sparks, probably ok, unless your wobby idle is misfires.
That's funny, now when you said it, when I rev the engine (slowly press the pedal), the engine starts to misfire. Didn't notice that before since we were just focusing on the idle.

We also removed the return line from the FPR, basically nothing comes out. Only a VERY small flow of fuel. The question is, is it the pump or the FPR then? I guess I need to investigate more.
 
#27 ·
I re-read your posts and I did not see you mention it, but did you check the Ignition timing?
If the ignition is way off you could get backfiring and rough idle.
It's pretty fundamental, but I tend to forget the fundamentals...
 
#28 ·
It's good to focus on fundamentals also - especially when I did not remember to mention everything.

Since I replaced the cam tower gaskets, I had to remove the belt and after that I naturally re-checked the timing. Also, the problem already existed before that also so nothing changed while adjusting the timing.

Once again, I really appreciate the time you guys use to help me with this problem.

BTW, I just received a fuel pressure meter so measuring the fuel pressure from the CSI my next step. I also found a replacement ECU from eBay and it should be here soon so at least we have some additional information if no root cause is found.
 
#31 ·
Turned the engine on today with a new fuel pump. Idle was slightly better than before so I started to think about the pressure regulator anyway. Also the CEL was still on. After a short moment I realized I still had not tried the other ECU I bought from eBay. Replaced the original with a new one and turned the key - damn, it works! No more CEL, no more wobby idling.

The only minor issue still remains; the can tower still leaks oil over the exhaust manifold but now I just need to open it again and apply some gasket maker to seal it properly.

I really appreciate your efforts, I know how frustrating it is to diagnose a car over the internet but I had plenty of good advice and tried to check those all. Thank you team!

Vehicle Automotive tire Hood Car Motor vehicle
 
  • Like
Reactions: supraz
#33 ·
When i had the head done may years ago (10+) i had the machine shop coat the metal cam tower gaskets on boths sides with a thin coating of Permatex Ultragray (82194). Worked like a charm and remains leak free today (wish I could say that for the rest of the engine...)

hth

will
 
  • Like
Reactions: FinToy
#34 ·
When i had the head done may years ago (10+) i had the machine shop coat the metal cam tower gaskets on boths sides with a thin coating of Permatex Ultragray (82194). Worked like a charm and remains leak free today (wish I could say that for the rest of the engine...)
Sounds good. I tried "Wurth Super RTV silicone plus" yesterday. I also found out why it was leaking: The Felpro gasket is a little bit too wide in the area marked in the picture and the gasket was bent there. I used Dremel tool to snap a little bit off the gasket and added sealant to the whole gasket on both sides. Let's hope it works now. Planning to start the engine today.
Automotive tire Motor vehicle Automotive design Automotive exterior Automotive wheel system
 
  • Like
Reactions: Zoe
This is an older thread, you may not receive a response, and could be reviving an old thread. Please consider creating a new thread.
Top